# 6384 3d printed propeller
**URL:** https://foil.zone/t/6384-3d-printed-propeller/14624
**Category:** Props & Ducts
**Created:** [November 29, 2021, 12:07pm UTC](https://foil.zone/t/6384-3d-printed-propeller/14624 "2021-11-29T12:07:39Z")
**Posts on this page:** 20
**Page:** 1
### Author:  [@marce002](https://foil.zone/u/marce002)
#### Post date: [November 29, 2021, 12:07pm UTC](https://foil.zone/t/6384-3d-printed-propeller/14624/1 "2021-11-29T12:07:39Z")
Can anyone share a 2 or 3 blade prop design/ STL for an 6384 outrunner? With tge 4 holes sligned… I will post results of its use / variations / plan to reinforce with epoxy…
---
### Author:  [@leachim](https://foil.zone/u/leachim)
#### Post date: [November 29, 2021, 3:57pm UTC](https://foil.zone/t/6384-3d-printed-propeller/14624/2 "2021-11-29T15:57:50Z")
Hi Marce,
you can use my folding Prop. Its based on the Prop of @V_S s fixed 2 blade prop. So you can also use his one. Just search our posts. They should be easy to find.
best regards Michael
---
### Author:  [@V\_S](https://foil.zone/u/V_S)
#### Post date: [November 29, 2021, 4:51pm UTC](https://foil.zone/t/6384-3d-printed-propeller/14624/3 "2021-11-29T16:51:21Z")
> **[3D design 156 0.39 1.09 15 4 Loch | Tinkercad](https://www.tinkercad.com/things/8Em45e37xbi)**
>
> 3D design 156 0.39 1.09 15 4 Loch created by blendezwonull with Tinkercad
Should work.
No need of reinforce.
---
### Author:  [@marce002](https://foil.zone/u/marce002)
#### Post date: [November 30, 2021, 12:09pm UTC](https://foil.zone/t/6384-3d-printed-propeller/14624/4 "2021-11-30T12:09:08Z")
Thanks you very much to both of you!
---
### Author:  [@mickeyt](https://foil.zone/u/mickeyt)
#### Post date: [December 1, 2021, 6:56am UTC](https://foil.zone/t/6384-3d-printed-propeller/14624/5 "2021-12-01T06:56:56Z")
> [@Bolt-on build in Perth](https://foil.zone/t/bolt-on-build-in-perth/10134):
>
> Our first build has been in progress for around 18 months. Went through a few iterations of boards, motors, props, etc. Ended up coming in at around AU$2,500 all told. Board - second hand ~$500 Battery - 13s9p (48V 20Ah) ~$500 Foil - Aliexpress - $700 Prop & motor mount - 3D printed Waterproof case $80 Motor - 8384 120kV direct drive outrunner - $80 ESC - 120A - $120 Controller - $50 Went through quite a few iterations on the propulsion system. Ended up going with a 150mm …
---
### Author:  [@NickOldfield](https://foil.zone/u/NickOldfield)
#### Post date: [June 27, 2022, 9:49am UTC](https://foil.zone/t/6384-3d-printed-propeller/14624/6 "2022-06-27T09:49:11Z")
Thanks for this design. I’m trying to learn more about propellers. Can you tell me what each of the parameters you have listed are for? Obviously 156 is the diameter but unsure what the rest correspond to.
Thanks.
---
### Author:  [@DanDyse](https://foil.zone/u/DanDyse)
#### Post date: [July 29, 2022, 1:48pm UTC](https://foil.zone/t/6384-3d-printed-propeller/14624/7 "2022-07-29T13:48:59Z")
Hey Volker, how does it perform? And is there a version that fits onto Flipsky 65161 motor?
Since I am a beginner at 3d printing - any material advise?
Thank you!
---
### Author:  [@Larsb](https://foil.zone/u/Larsb)
#### Post date: [August 29, 2022, 4:48pm UTC](https://foil.zone/t/6384-3d-printed-propeller/14624/8 "2022-08-29T16:48:20Z")
156 diameter, 0.39 Area ratio, 1.09 pitch/dia, means pitch is 1.09\*156/25.4 = 6.7inches
---
### Author:  [@V\_S](https://foil.zone/u/V_S)
#### Post date: [September 3, 2022, 10:06pm UTC](https://foil.zone/t/6384-3d-printed-propeller/14624/9 "2022-09-03T22:06:38Z")
Have a look [here](https://foil.zone/t/shorty-2-volker-s-third/16619)
---
### Author:  [@punk25830](https://foil.zone/u/punk25830)
#### Post date: [May 18, 2023, 12:14am UTC](https://foil.zone/t/6384-3d-printed-propeller/14624/10 "2023-05-18T00:14:20Z")
How much do you weigh and what accessories would you replace if you upgraded
---
### Author:  [@FoiledBySpoil](https://foil.zone/u/FoiledBySpoil)
#### Post date: [February 24, 2024, 8:55am UTC](https://foil.zone/t/6384-3d-printed-propeller/14624/11 "2024-02-24T08:55:26Z")
@V_S have you tested your props with a 6384 or 6374 assist on 12s or 10s? Or perhaps someone else? I tried the 1.09 with 6374 but only with 8s not suffucient no surprise, going 12s soon
---
### Author:  [@V\_S](https://foil.zone/u/V_S)
#### Post date: [February 24, 2024, 8:58am UTC](https://foil.zone/t/6384-3d-printed-propeller/14624/12 "2024-02-24T08:58:43Z")
they are optimised for 12s.
[88cm](https://foil.zone/t/88cm-volkers-fifth/20117) first Test was with 154 1,0
Updated Version, including support for easy printing:
> **[3D design 6384 154 0,4 1.1 | Tinkercad](https://www.tinkercad.com/things/lWjqYRA8rTa-6384-154-04-11)**
>
> 3D design 6384 154 0,4 1.1 created by blendezwonull with Tinkercad
---
### Author:  [@Jatem](https://foil.zone/u/Jatem)
#### Post date: [February 24, 2024, 7:36pm UTC](https://foil.zone/t/6384-3d-printed-propeller/14624/13 "2024-02-24T19:36:01Z")
Is PLA your preferred filament for the prop? How is the durability, and would you suggest the blades are printed with a high wall count for strength?
---
### Author:  [@heiguga](https://foil.zone/u/heiguga)
#### Post date: [April 28, 2024, 12:26pm UTC](https://foil.zone/t/6384-3d-printed-propeller/14624/14 "2024-04-28T12:26:04Z")
Is it possible to get the same propeller for the opposite direction (for a two motor tow buddy)? Thanks in advance. I will share three design files for my tow buddy soon. Still need a propeller solution to test it…
---
### Author:  [@windego](https://foil.zone/u/windego)
#### Post date: [April 28, 2024, 1:36pm UTC](https://foil.zone/t/6384-3d-printed-propeller/14624/15 "2024-04-28T13:36:12Z")
you can use tinkercad to mirror it and get opposite rotation.
---
### Author:  [@heiguga](https://foil.zone/u/heiguga)
#### Post date: [April 28, 2024, 3:23pm UTC](https://foil.zone/t/6384-3d-printed-propeller/14624/16 "2024-04-28T15:23:47Z")
thank you. Sometimes my brain needs a small push… 🙂
---
### Author:  [@rttn](https://foil.zone/u/rttn)
#### Post date: [April 28, 2024, 3:51pm UTC](https://foil.zone/t/6384-3d-printed-propeller/14624/17 "2024-04-28T15:51:31Z")
This can be done directly in a slicer, such as Bambu Studio or Orca Slicer.
---
### Author:  [@Savoie](https://foil.zone/u/Savoie)
#### Post date: [August 24, 2024, 5:06am UTC](https://foil.zone/t/6384-3d-printed-propeller/14624/18 "2024-08-24T05:06:55Z")
> [@V\_S](#):
>
> Updated Version, including support for easy printing:
>
> [3D design 6384 154 0,4 1.1 - Tinkercad](https://www.tinkercad.com/things/lWjqYRA8rTa-6384-154-04-11)
1.1 is optimized for 12S or is it the 1.09?
---
### Author:  [@KLAUSMOLLERZIP](https://foil.zone/u/KLAUSMOLLERZIP)
#### Post date: [August 28, 2024, 2:35am UTC](https://foil.zone/t/6384-3d-printed-propeller/14624/19 "2024-08-28T02:35:23Z")
Hi, do these design match the rotor mounting screws of the new Flipsky 6384?
thanks
---
### Author:  [@superlefax](https://foil.zone/u/superlefax)
#### Post date: [August 28, 2024, 9:54pm UTC](https://foil.zone/t/6384-3d-printed-propeller/14624/20 "2024-08-28T21:54:01Z")
Hi Klaus! I can do a special Fold Version for you with clockwise spinning FOLD wich fits to the new Flipsky motor. Just write me on [sales@propellerking.com](mailto:sales@propellerking.com)
[Next page](https://foil.zone/t/6384-3d-printed-propeller/14624.md?page=2)