# 65161 + FSESC 200A 60V VESC Settings
**URL:** https://foil.zone/t/65161-fsesc-200a-60v-vesc-settings/15760
**Category:** Electronics (ESC, remote, batteries)
**Created:** [May 21, 2022, 9:12am UTC](https://foil.zone/t/65161-fsesc-200a-60v-vesc-settings/15760 "2022-05-21T09:12:14Z")
**Posts on this page:** 11
**Page:** 1
### Author:  [@FunkyBunch](https://foil.zone/u/FunkyBunch)
#### Post date: [May 21, 2022, 9:12am UTC](https://foil.zone/t/65161-fsesc-200a-60v-vesc-settings/15760/1 "2022-05-21T09:12:14Z")
Hello,
Would anyone be able to share their configuration file or list the settings used for this configuration please. I have gone through this thread but have not had success with any settings yet \> [VESC Tool thread - how to program](https://foil.zone/t/vesc-tool-thread-how-to-program/9670)
I have water tested the board but it was very low on power. BLDC seems very rough with my settings.
Setup:
65161 Motor
FSESC 200A 60V ESC
12S12P Battery
Thanks!
---
### Author:  [@Scripto](https://foil.zone/u/Scripto)
#### Post date: [May 22, 2022, 1:50pm UTC](https://foil.zone/t/65161-fsesc-200a-60v-vesc-settings/15760/2 "2022-05-22T13:50:34Z")
I hope someone can provide some help you, I have the same question. Following the included instructions and online recommendations didn’t seem to to do it.
---
### Author:  [@Malveymonster](https://foil.zone/u/Malveymonster)
#### Post date: [May 24, 2022, 6:00pm UTC](https://foil.zone/t/65161-fsesc-200a-60v-vesc-settings/15760/3 "2022-05-24T18:00:32Z")
I’m in the same boat. My wiring is good (the motor spun properly during the setup), but while trying to connect my controller, the tool said I needed to update my firmware. I updated it, and now the motor is jittering and overheating when I try to make it spin. I believe the issue was forgetting to disable phase filtering, but I don’t know where to go from here. I don’t know if the esc or motor is damaged, or if it’s just a firmware issue.
I’ll report back if I get my setup to work, but hopefully someone else who knows more can help out.
---
### Author:  [@Malveymonster](https://foil.zone/u/Malveymonster)
#### Post date: [May 26, 2022, 1:42am UTC](https://foil.zone/t/65161-fsesc-200a-60v-vesc-settings/15760/4 "2022-05-26T01:42:23Z")
Yo I just got mine to work. I have the same motor, battery, and esc configuration. I can’t guarantee anything, but let me know what questions you have and I might be able to help.
---
### Author:  [@Malveymonster](https://foil.zone/u/Malveymonster)
#### Post date: [May 26, 2022, 1:42am UTC](https://foil.zone/t/65161-fsesc-200a-60v-vesc-settings/15760/5 "2022-05-26T01:42:53Z")
What problems are you having? I might be able to help.
---
### Author:  [@Scripto](https://foil.zone/u/Scripto)
#### Post date: [May 30, 2022, 5:42pm UTC](https://foil.zone/t/65161-fsesc-200a-60v-vesc-settings/15760/6 "2022-05-30T17:42:21Z")
What did you do that ended up working? I guess if you have a moment a brief list of things would be helpful. I.e. which vesctool version, firmware version, settings, etc. Thanks.
---
### Author:  [@Malveymonster](https://foil.zone/u/Malveymonster)
#### Post date: [June 3, 2022, 4:35am UTC](https://foil.zone/t/65161-fsesc-200a-60v-vesc-settings/15760/7 "2022-06-03T04:35:16Z")
[This](https://foil.zone/t/vesc-setup-help-please/15776) is a link to a different post that goes over what my problem was, as well as some solutions. I hope it helps.
---
### Author:  [@FunkyBunch](https://foil.zone/u/FunkyBunch)
#### Post date: [June 5, 2022, 2:25pm UTC](https://foil.zone/t/65161-fsesc-200a-60v-vesc-settings/15760/8 "2022-06-05T14:25:20Z")
I initially had it setup with default firmware which was limiting the Motor Current too much.
I am now using the unrestricted version and this is much better.
My issue is when approaching full load the motor stutters and loses power.
I am using FOC mode. What settings influence this stuttering?
---
### Author:  [@Scripto](https://foil.zone/u/Scripto)
#### Post date: [June 13, 2022, 7:38pm UTC](https://foil.zone/t/65161-fsesc-200a-60v-vesc-settings/15760/9 "2022-06-13T19:38:47Z")
What vesc firmware are you using? I had the same problem and downgraded to 5.1 wifi solved my problem
---
### Author:  [@FunkyBunch](https://foil.zone/u/FunkyBunch)
#### Post date: [June 19, 2022, 9:06am UTC](https://foil.zone/t/65161-fsesc-200a-60v-vesc-settings/15760/10 "2022-06-19T09:06:58Z")
I am running 5.2
Where can I download 5.1?
---
### Author:  [@sat\_be](https://foil.zone/u/sat_be)
#### Post date: [June 19, 2022, 10:06am UTC](https://foil.zone/t/65161-fsesc-200a-60v-vesc-settings/15760/11 "2022-06-19T10:06:40Z")
Here: [Precompiled VESC Tool Archive - The Citadel - Essential References for Esk8 - esk8.news: DIY Electric Skateboard Forums](https://forum.esk8.news/t/precompiled-vesc-tool-archive/15920)