# Cedar build from Idaho complete!

**URL:** https://foil.zone/t/cedar-build-from-idaho-complete/15623
**Category:** Builds
**Created:** [April 30, 2022, 4:50pm UTC](https://foil.zone/t/cedar-build-from-idaho-complete/15623 "2022-04-30T16:50:45Z")
**Posts on this page:** 5
**Page:** 1

<div class="post-metadata">

### Author: ![NDH](https://foil.zone/letter_avatar_proxy/v4/letter/n/54ee81/32.png) [@NDH](https://foil.zone/u/NDH)
#### Post date: [April 30, 2022, 4:50pm UTC](https://foil.zone/t/cedar-build-from-idaho-complete/15623/1 "2022-04-30T16:50:45Z")

</div>

![20220430_084140](https://foil.zone/uploads/default/original/3X/0/9/099714d77cca889d6750d58f7141a661783ab6b8.jpeg)

Board with battery installed. Secured by 2 PETG retaining clips.

 ![20220430_091958](https://foil.zone/uploads/default/original/3X/c/c/cc207f7e413ffd7c79cf7d795c021fb71a04fa78.jpeg)

 ![20220430_091902](https://foil.zone/uploads/default/original/3X/d/8/d860c0b7b29e1020d8ac0caf6dc72f9b1cd9ab35.jpeg)

Retaining clip detail (unclipped in photo)

 ![20220430_091953](https://foil.zone/uploads/default/original/3X/e/b/eb0aba900786fa8fa4259d22a661aeaff5ef0116.jpeg)

Battery is 21700 14S 10P with 300amp fuse and ANT BMS. In polycarbonate case, fiber glassed with PETG handle. handle has imbedded AMASS 150 plugs (male plug has O rings) that mate with mast top waterproof ESC/BEC/water pump/receiver case.

 ![20220430_091409](https://foil.zone/uploads/default/original/3X/7/5/7511a8201e86d388a7b252750834749e1c33abd8.jpeg)

With mast top ESC box mated with battery in board.

 ![20220430_0953511](https://foil.zone/uploads/default/original/3X/7/7/7773b7850ef6f173c161f15d500df96aa3419681.jpeg)

Mast top AMASS plugs that mate with battery.

 ![20220430_091417](https://foil.zone/uploads/default/original/3X/4/4/4486ca515c9c34461bb91bfa6c37071590b8dbea.jpeg)

Dead man switch that kills BEC input to receiver with weight is removed from board lid.

 ![20220430_092112](https://foil.zone/uploads/default/original/3X/3/c/3c22699be79cfc5b7bb02c281e6d1909b1084fca.jpeg)

Underside of lid with PETG compression ring that mates with EPDM top gasket and step downs to further secure battery and to activate dead man switch when weighted.

 ![20220430_091202](https://foil.zone/uploads/default/original/3X/1/a/1a10f834580b3f39e6aa7c663eed37249e94302c.jpeg)

Lid secured with 6 bolts.

 ![20220430_084615](https://foil.zone/uploads/default/original/3X/1/b/1b61cb924164114f1d5224f697b293fd7dc126d8.jpeg)

Silicon gasket and battery handle with switch. Ready for mast install.

 ![20220430_091601](https://foil.zone/uploads/default/original/3X/2/6/2636f61dfea17114a2868d40635418f9bd8e4dab.jpeg)

Mast installed. 4 bolts. coolant water exit port in front of mast.

 ![20220430_091227](https://foil.zone/uploads/default/original/3X/5/0/50418e3b00c4aa764603490522c8bc48e354efe6.jpeg)

```auto
![20220203_083952|375x500](upload://7HUDdPuQ1NKDs6eYABwHYVbp1Xv.jpeg)

Maytech remote with a facelift. ASA. Fully waterproof and floats!

```

 ![20220430_091237](https://foil.zone/uploads/default/original/3X/1/f/1faafb87fc84cc879aa91bb72065b3b9c0ce7db1.jpeg)  
 ![20220430_091227](https://foil.zone/uploads/default/original/3X/5/0/50418e3b00c4aa764603490522c8bc48e354efe6.jpeg)

Tip and tail of bookended blocking. hollow core with 4-6 mm cedar planking and 6 OZ S glass/epoxy. Learned a lot from Sliver Paddleboard website. Sells kits and has good instructions. Thanks! Drew this in Fussion 360, sectioned it and cut frame on Router.

 ![20220430_091216](https://foil.zone/uploads/default/original/3X/f/2/f2b3f47323dfdc4143de1e695568f491749f29c1.jpeg)  
 ![20220430_091607](https://foil.zone/uploads/default/original/3X/2/d/2dec18c697e246a44362c06ab9fc5169b58a1f6a.jpeg)

 ![20220430_091554](https://foil.zone/uploads/default/original/3X/a/c/acbeeb8d04464f9cd903c0e9d3d144a49190527e.jpeg)

Water inlet on clamp front. This is a PETG sleeve over the clamp. Non-structural.

 ![20220203_083850](https://foil.zone/uploads/default/original/3X/9/7/97cacf5913d0e5ab2414d2088ce9fc8a0fd48315.jpeg)

Clamp with sleeve removed. 4 threaded stainless rods through PETG clamp with AL plate. no structural plastic parts in clamp. (sorry poor picture)

 ![20220430_091034](https://foil.zone/uploads/default/original/3X/a/3/a3b12f4e80575692098155e09a80f4768c2dbbd2.jpeg)  
 ![20220430_091621](https://foil.zone/uploads/default/original/3X/d/b/db4a595ddb18731efaac3448f0756f3c5787c966.jpeg)

---

<div class="post-metadata">

### Author: ![Lake\_flyer](https://foil.zone/letter_avatar_proxy/v4/letter/l/ec9cab/32.png) [@Lake\_flyer](https://foil.zone/u/Lake_flyer)
#### Post date: [May 1, 2022, 3:25am UTC](https://foil.zone/t/cedar-build-from-idaho-complete/15623/2 "2022-05-01T03:25:10Z")

</div>

Beautiful work here.  
What motor did you go with?

---

<div class="post-metadata">

### Author: ![NDH](https://foil.zone/letter_avatar_proxy/v4/letter/n/54ee81/32.png) [@NDH](https://foil.zone/u/NDH)
#### Post date: [May 1, 2022, 4:04am UTC](https://foil.zone/t/cedar-build-from-idaho-complete/15623/3 "2022-05-01T04:04:18Z")

</div>

Flipsky 65161 with threads, Seal 300A ESC.

---

<div class="post-metadata">

### Author: ![hovav](https://foil.zone/user_avatar/foil.zone/hovav/32/11423_2.png) [@hovav](https://foil.zone/u/hovav)
#### Post date: [May 1, 2022, 5:53am UTC](https://foil.zone/t/cedar-build-from-idaho-complete/15623/4 "2022-05-01T05:53:52Z")

</div>

Amazing work !  
How much does it weigh ?

---

<div class="post-metadata">

### Author: ![NDH](https://foil.zone/letter_avatar_proxy/v4/letter/n/54ee81/32.png) [@NDH](https://foil.zone/u/NDH)
#### Post date: [May 7, 2022, 8:24pm UTC](https://foil.zone/t/cedar-build-from-idaho-complete/15623/5 "2022-05-07T20:24:08Z")

</div>

Board is 26lbs  
Mast etc… 17.5lbs  
Battery is 27.5lbs

Total 71lbs