# Cutoff problem SEAKING 130

**URL:** https://foil.zone/t/cutoff-problem-seaking-130/1718
**Category:** Electronics (ESC, remote, batteries)
**Created:** [May 13, 2018, 7:40am UTC](https://foil.zone/t/cutoff-problem-seaking-130/1718 "2018-05-13T07:40:21Z")
**Posts on this page:** 6
**Page:** 1

<div class="post-metadata">

### Author: ![Frage](https://foil.zone/letter_avatar_proxy/v4/letter/f/91b2a8/32.png) [@Frage](https://foil.zone/u/Frage)
#### Post date: [May 13, 2018, 7:40am UTC](https://foil.zone/t/cutoff-problem-seaking-130/1718/1 "2018-05-13T07:40:21Z")

</div>

Hi

I did not have time to burn my own Seaking ESC yet - that’s is already a good point 😉

During my tests in the wate (motor + foil + board + human), the ESC cuts the power all the time.  
Outside the water it is ok, but inside when I reach 30% of the throttle the motor is stopped .  
My batteries are new and fully charged - 12S Kypom 12000mhA 25C

is there somebody who had this problem and who has changed the default parameters of the Seaking with the programming mode or usb interface ?

thanks for your answer…

---

<div class="post-metadata">

### Author: ![Ralf](https://foil.zone/user_avatar/foil.zone/ralf/32/2265_2.png) [@Ralf](https://foil.zone/u/Ralf)
#### Post date: [May 13, 2018, 9:18am UTC](https://foil.zone/t/cutoff-problem-seaking-130/1718/2 "2018-05-13T09:18:35Z")

</div>

Hi, which engine do you have?

---

<div class="post-metadata">

### Author: ![superlefax](https://foil.zone/user_avatar/foil.zone/superlefax/32/13626_2.png) [@superlefax](https://foil.zone/u/superlefax)
#### Post date: [May 13, 2018, 10:45am UTC](https://foil.zone/t/cutoff-problem-seaking-130/1718/3 "2018-05-13T10:45:24Z")

</div>

And what is your prop size and gear reduction?

---

<div class="post-metadata">

### Author: ![Frage](https://foil.zone/letter_avatar_proxy/v4/letter/f/91b2a8/32.png) [@Frage](https://foil.zone/u/Frage)
#### Post date: [May 13, 2018, 11:18am UTC](https://foil.zone/t/cutoff-problem-seaking-130/1718/4 "2018-05-13T11:18:51Z")

</div>

Hi,

I use SSS 500kv / 1:5 gearbox and the propeller with 3 blades (the one proposed by pacificMeister)

… I changed nothing of the proposed solution by pacificMeister

---

<div class="post-metadata">

### Author: ![pacificmeister](https://foil.zone/user_avatar/foil.zone/pacificmeister/32/8_2.png) [@pacificmeister](https://foil.zone/u/pacificmeister)
#### Post date: [May 13, 2018, 12:54pm UTC](https://foil.zone/t/cutoff-problem-seaking-130/1718/5 "2018-05-13T12:54:31Z")

</div>

Strange. Any idea what amps you pull? Maybe the motor get out of sync at higher load, feels like esc cut power. Had it only with direct drives so far. Is everything dry?

---

<div class="post-metadata">

### Author: ![Frage](https://foil.zone/letter_avatar_proxy/v4/letter/f/91b2a8/32.png) [@Frage](https://foil.zone/u/Frage)
#### Post date: [May 13, 2018, 2:15pm UTC](https://foil.zone/t/cutoff-problem-seaking-130/1718/6 "2018-05-13T14:15:13Z")

</div>

I have not place to put a system to monitor the amps. everything looks dry. maybe can I change the Timing (did you do it pacificmeister ?) ? The board is maybe not really adapted and the rider to heavy ? 😉

Maybe the voltage cutoff is too high ?