# DIY mast & wing sheap
**URL:** https://foil.zone/t/diy-mast-wing-sheap/605
**Category:** Foils & Boards
**Created:** [November 9, 2017, 3:34pm UTC](https://foil.zone/t/diy-mast-wing-sheap/605 "2017-11-09T15:34:31Z")
**Posts on this page:** 9
**Page:** 5
### Author:  [@Toto44](https://foil.zone/u/Toto44)
#### Post date: [October 21, 2022, 3:46pm UTC](https://foil.zone/t/diy-mast-wing-sheap/605/83 "2022-10-21T15:46:09Z")
The 63100 outrunner on 12 s will lift your fat ass out of the water without any problems.
Get a Flycolor HV 150A esc it will be around 90us$ and go.
I run this combo with a gong curve L wing for 2 years without any problems.
I am 80 kg and got on wing with 60% of max power.
---
### Author:  [@Felixxx](https://foil.zone/u/Felixxx)
#### Post date: [October 21, 2022, 4:17pm UTC](https://foil.zone/t/diy-mast-wing-sheap/605/84 "2022-10-21T16:17:34Z")
Do you have any link for motor your mention?
I will go for outrunner.
Tnx
For now motor problem solved
---
### Author:  [@Toto44](https://foil.zone/u/Toto44)
#### Post date: [October 21, 2022, 4:36pm UTC](https://foil.zone/t/diy-mast-wing-sheap/605/85 "2022-10-21T16:36:57Z")
> **[aps-63100-sensored-outrunner-brushless-motor-140kv-4500w](https://alienpowersystem.com/shop/brushless-motors/63mm/aps-63100-sensored-outrunner-brushless-motor-140kv-4500w/)**
>
> aps-63100-sensored-outrunner-brushless-motor-140kv-4500w
---
### Author:  [@Toto44](https://foil.zone/u/Toto44)
#### Post date: [October 21, 2022, 4:38pm UTC](https://foil.zone/t/diy-mast-wing-sheap/605/86 "2022-10-21T16:38:47Z")
> **[88.0US $ |1pcs Flycolor Flydragon 150a Esc 5-12s Hv Opto For Rc Hobby Model...](https://www.aliexpress.com/i/2255799931469617.html?gatewayAdapt=deu2glo4itemAdapt)**
>
> Smarter Shopping, Better Living! Aliexpress.com
This one will need bigger cooler
---
### Author:  [@newguy](https://foil.zone/u/newguy)
#### Post date: [April 4, 2026, 3:21pm UTC](https://foil.zone/t/diy-mast-wing-sheap/605/87 "2026-04-04T15:21:11Z")
I plan to glue PLA 3d printed segments together to about 3 feet. Load epoxy infill through the cut open sides, laminate in about 6 layers of carbon fiber. Comments?
---
### Author:  [@sat\_be](https://foil.zone/u/sat_be)
#### Post date: [April 4, 2026, 4:36pm UTC](https://foil.zone/t/diy-mast-wing-sheap/605/88 "2026-04-04T16:36:29Z")
Better print two moulds and lamintae two halfs with some layers. Sand to fit and put in as much fiber you can fit, 45 degree biax and unidirectional as well.
---
### Author:  [@newguy](https://foil.zone/u/newguy)
#### Post date: [April 5, 2026, 10:29am UTC](https://foil.zone/t/diy-mast-wing-sheap/605/89 "2026-04-05T10:29:17Z")
Thanks. Reflecting on your message, I realized that I have a conceptual misunderstanding. I will spend more time looking into this. Anything you can share is greatly appreciated.
---
### Author:  [@newguy](https://foil.zone/u/newguy)
#### Post date: [April 5, 2026, 10:53am UTC](https://foil.zone/t/diy-mast-wing-sheap/605/90 "2026-04-05T10:53:55Z")
My initial reaction, per your comment - two molds - two carbon fiber parts with 45 degree biax and unidirectional. 6- 8 layers. More? Change in geometry. 2-3 centimeters next to the edge are flat on both ends, so it is simple to understand how much (and how) fiber to load. Sandwich - carbon part from molding, carbon fiber (3-4?) with epoxy and another carbon part. Weight on the top. Center is hollow.
---
### Author:  [@sat\_be](https://foil.zone/u/sat_be)
#### Post date: [April 5, 2026, 2:14pm UTC](https://foil.zone/t/diy-mast-wing-sheap/605/91 "2026-04-05T14:14:20Z")
See here how I built my mast, I still use it. It could be more stable but it is ok, put in as much fiber as you can fit in.
> [@Daniel's 2nd build](https://foil.zone/t/daniels-2nd-build/19956/2):
>
> Mast: The mast was built the same way as the wings. The mold is slightly more complicated as it consists of more than two parts. Design is from @visor360. Glued the pieces and aligned them to be straight/90° respectively Reinforced it with wood and glassed it over on the outside Built an insert from forged carbon to hold the FR motor. The insert was built with a 2 part mold, filled with epoxy and cfk flakes pressed together. Pin holes to fix the motor w…
[Previous page](https://foil.zone/t/diy-mast-wing-sheap/605.md?page=4)