# DIY super simple hassle-free Cable-Remote
**URL:** https://foil.zone/t/diy-super-simple-hassle-free-cable-remote/13936
**Category:** Electronics (ESC, remote, batteries)
**Tags:** remote-control, remote
**Created:** [September 10, 2021, 4:51pm UTC](https://foil.zone/t/diy-super-simple-hassle-free-cable-remote/13936 "2021-09-10T16:51:37Z")
**Posts on this page:** 19
**Page:** 1
### Author:  [@HamburgHarbourFoiler](https://foil.zone/u/HamburgHarbourFoiler)
#### Post date: [September 10, 2021, 4:51pm UTC](https://foil.zone/t/diy-super-simple-hassle-free-cable-remote/13936/1 "2021-09-10T16:51:38Z")
Since we’re all still having troubles with all that wireless remotes and there are no actually good remotes on the market that just work for long time without electrical engineers fixing them from time to time, I thought about developing a **cable** **remote** with this community.
- No battery that need to be charged
- No fancy electronics to get water damaged
- DIY so everyone can built it with simple and cheap components
- No way to lose it since its tied by cabel
So how to do that? Here are my thoughts:
Princip: HALL sensor with magnet in housing. Connected by wire to ESC. Power for HALL sensor by ESC. Nothing else!
Top level requirements:
- Watertight
- corrosion resistant
- pull resistant
- easy to built
- no way to accidentally apply throttle ( 2-step activation?)
**Sensing:** HALL sensor paired with a magnet on a spring actuated lever (pistol trigger style) (maybe don’t use a steel spring du to corrosion and integrate spring into printed part)
**Housing:** FDM 3D Printed ABS ( no need for water tightness as sensor and cable will be soaked into water tight stuff like “PlastiDip” )
**Cable:** Repurpose any 1.5 to 2.0m USB cable (4 wires and often kevlar reinforced for pulling). Cut off small connector and solder onto hall sensor.
**Connection to eFoil:** just a hole with watertight seal OR watertight USB socket to unplug the Remote (sense?)
**Connection to ESC:** For VESC you can just hook it up as analoge input, for any PWM esc you need device to convert analoge to PWM (arduino, or a special IC?)
So, what do you think?
---
### Author:  [@Jaap](https://foil.zone/u/Jaap)
#### Post date: [September 11, 2021, 6:42am UTC](https://foil.zone/t/diy-super-simple-hassle-free-cable-remote/13936/3 "2021-09-11T06:42:38Z")
I haven’t finished my first build yet. Based on many hours of reading on this forum (which is awesome btw!), I’m thinking about using a wired control too. This in combination with a leash, in order not to loose the board when it gets grabbed by a wave. (I will be using it at sea).
I’m curious about any technical ideas from the more experienced builders
---
### Author:  [@XSailor](https://foil.zone/u/XSailor)
#### Post date: [September 11, 2021, 7:31am UTC](https://foil.zone/t/diy-super-simple-hassle-free-cable-remote/13936/4 "2021-09-11T07:31:09Z")
The combustion engine jet surfboards seams to use cable remotes and a leash, for sure would work on a foil also. My plan is to do the same, maybe utilizing a servo tester.
---
### Author:  [@Toto44](https://foil.zone/u/Toto44)
#### Post date: [September 11, 2021, 11:21am UTC](https://foil.zone/t/diy-super-simple-hassle-free-cable-remote/13936/5 "2021-09-11T11:21:01Z")
I did something like this on my towbogie. Just a simple thumb throttle and servo testet. If you use vesc you can even skip the servo tester and connect the thump throttle directly
---
### Author:  [@Toto44](https://foil.zone/u/Toto44)
#### Post date: [September 11, 2021, 11:21am UTC](https://foil.zone/t/diy-super-simple-hassle-free-cable-remote/13936/6 "2021-09-11T11:21:39Z")
[https://www.instagram.com/p/CLPrcQJrsWF/?utm\_medium=copy\_link](https://www.instagram.com/p/CLPrcQJrsWF/?utm_medium=copy_link)
---
### Author:  [@tacktun](https://foil.zone/u/tacktun)
#### Post date: [September 11, 2021, 5:47pm UTC](https://foil.zone/t/diy-super-simple-hassle-free-cable-remote/13936/7 "2021-09-11T17:47:34Z")
Nice Idea to use a dirt cheap thumb throttle.
Can you just plug it into the VESC and adjust the range with the vesc-tool, or do you have an Arduino in between to sort out the signal?
And how did you manage the waterproofing?
---
### Author:  [@tacktun](https://foil.zone/u/tacktun)
#### Post date: [September 11, 2021, 5:48pm UTC](https://foil.zone/t/diy-super-simple-hassle-free-cable-remote/13936/8 "2021-09-11T17:48:41Z")
And a thumb throttle doesn’t have a brake function does it?
---
### Author:  [@XSailor](https://foil.zone/u/XSailor)
#### Post date: [September 11, 2021, 5:55pm UTC](https://foil.zone/t/diy-super-simple-hassle-free-cable-remote/13936/9 "2021-09-11T17:55:25Z")
Here some instructions for those not having an vesc
[http://gamba.dk/index.php/projekter/2016-06-15-20-33-39](http://gamba.dk/index.php/projekter/2016-06-15-20-33-39)
Would like to replace the servo tester with something of higher quality but have not find anything suitable.
---
### Author:  [@Toto44](https://foil.zone/u/Toto44)
#### Post date: [September 11, 2021, 9:17pm UTC](https://foil.zone/t/diy-super-simple-hassle-free-cable-remote/13936/10 "2021-09-11T21:17:12Z")
Yes. You need 5v gnd and the signal from the hall sensor to ADC1 the rest over vesc tool
---
### Author:  [@tacktun](https://foil.zone/u/tacktun)
#### Post date: [September 12, 2021, 7:54am UTC](https://foil.zone/t/diy-super-simple-hassle-free-cable-remote/13936/11 "2021-09-12T07:54:06Z")
Nice.
How is it holding up in the water ?
---
### Author:  [@Toto44](https://foil.zone/u/Toto44)
#### Post date: [September 12, 2021, 8:44am UTC](https://foil.zone/t/diy-super-simple-hassle-free-cable-remote/13936/12 "2021-09-12T08:44:50Z")
Well it is simple mechanics mostly plastic. Nothing that can be damaged by water. Just little rust checking from time to time for the spring.
---
### Author:  [@Jatem](https://foil.zone/u/Jatem)
#### Post date: [September 12, 2021, 7:53pm UTC](https://foil.zone/t/diy-super-simple-hassle-free-cable-remote/13936/13 "2021-09-12T19:53:49Z")
How is the v shaped hull on your tow boogie working out?
---
### Author:  [@Jezza](https://foil.zone/u/Jezza)
#### Post date: [September 13, 2021, 1:19pm UTC](https://foil.zone/t/diy-super-simple-hassle-free-cable-remote/13936/14 "2021-09-13T13:19:25Z")
> **[Rewinch Rider Remote](https://rewinch.com/collections/all/products/rewinch-rider-remote)**
>
> Rewinch Rider Remote If you want to get a “solo” experience or if you just like to control your pull and build your skills, then rewinch rider remote is for you! It’s a fully waterproof device and has smart features and quick changeable settings so...
---
### Author:  [@JetboardCologne](https://foil.zone/u/JetboardCologne)
#### Post date: [September 20, 2021, 5:11pm UTC](https://foil.zone/t/diy-super-simple-hassle-free-cable-remote/13936/16 "2021-09-20T17:11:24Z")
Those who have already foiled don’t want an annoying cable.
A cable is unnecessary and dangerous, especially with remote control, which works well from $ 20.
Greetings Frank
---
### Author:  [@Jatem](https://foil.zone/u/Jatem)
#### Post date: [September 20, 2021, 8:24pm UTC](https://foil.zone/t/diy-super-simple-hassle-free-cable-remote/13936/17 "2021-09-20T20:24:55Z")
Which $20 remote are you referring to? I could do with a spare.
---
### Author:  [@e-Jetter](https://foil.zone/u/e-Jetter)
#### Post date: [September 22, 2021, 9:16am UTC](https://foil.zone/t/diy-super-simple-hassle-free-cable-remote/13936/18 "2021-09-22T09:16:59Z")
[https://a.aliexpress.com/\_uui7yC](https://a.aliexpress.com/_uui7yC)
[https://a.aliexpress.com/\_u70Xqk](https://a.aliexpress.com/_u70Xqk)
---
### Author:  [@SoEFoil](https://foil.zone/u/SoEFoil)
#### Post date: [September 23, 2021, 9:04pm UTC](https://foil.zone/t/diy-super-simple-hassle-free-cable-remote/13936/19 "2021-09-23T21:04:22Z")
This solution presents some risks when you don"t have time to release your index from the thumb throttle and are ejected from the efoil board.
---
### Author:  [@XSailor](https://foil.zone/u/XSailor)
#### Post date: [September 24, 2021, 5:03am UTC](https://foil.zone/t/diy-super-simple-hassle-free-cable-remote/13936/20 "2021-09-24T05:03:24Z")
Yes, and also the return spring can get jammed…Believe a kill switch with leash is way to go is the solution then remote controller or cable remote.
---
### Author:  [@Larsb](https://foil.zone/u/Larsb)
#### Post date: [August 25, 2022, 3:50pm UTC](https://foil.zone/t/diy-super-simple-hassle-free-cable-remote/13936/21 "2022-08-25T15:50:15Z")
Been running wired since two years, no safety cutoff needed as throttle inevitably leaves your hand. My board stops immediately.
I don’t find it troublesome, more thinking it would be annoying to swim with a hand held remote