# ESC Flycolor X Cross HV3 settings on BlHeli 32
**URL:** https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725
**Category:** Electronics (ESC, remote, batteries)
**Created:** [December 4, 2023, 5:59pm UTC](https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725 "2023-12-04T17:59:42Z")
**Posts on this page:** 20
**Page:** 3
### Author:  [@Etiennebzh](https://foil.zone/u/Etiennebzh)
#### Post date: [March 11, 2024, 8:05pm UTC](https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725/41 "2024-03-11T20:05:34Z")
I have to disconnect the plug with +/gnd/signal because they are connected together on the same plug and this one go on the usb chip.
---
### Author:  [@lishine](https://foil.zone/u/lishine)
#### Post date: [March 11, 2024, 8:19pm UTC](https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725/42 "2024-03-11T20:19:24Z")
Thanks, but I don’t quite understand
---
### Author:  [@nicolasLGM](https://foil.zone/u/nicolasLGM)
#### Post date: [March 13, 2024, 4:09pm UTC](https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725/43 "2024-03-13T16:09:37Z")
Hi,
I’m coming back to you with a problem on my Flycolor xcross HV3 120A ESC, which beeps as soon as I pull the trigger but without starting the motor, just after 3 sessions that worked fine.
I tested everything (other motor, other remote control, other receiver, everything works fine on my other boxes), I reinitialized the ESC via the blheli PC application, I checked the continuity of the 3 phases, I also checked the ESC calibration hypothesis, I performed the recalibration operation with the beeps, but nothing helped. I also check the 3 phase cables are OK. No problem connecting to the ESC via the usb dongle. What analysis and solution can you suggest?
Thanks
---
### Author:  [@lishine](https://foil.zone/u/lishine)
#### Post date: [March 13, 2024, 5:21pm UTC](https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725/44 "2024-03-13T17:21:47Z")
Maybe this helps:
'[Maytech motor beeps - doesn't work](https://foil.zone/t/maytech-motor-beeps-doesnt-work/16769)
Bec problem
---
### Author:  [@Toto44](https://foil.zone/u/Toto44)
#### Post date: [March 14, 2024, 6:35am UTC](https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725/45 "2024-03-14T06:35:45Z")
What voltage you use for the receiver/esc?
---
### Author:  [@Etiennebzh](https://foil.zone/u/Etiennebzh)
#### Post date: [March 14, 2024, 7:56am UTC](https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725/46 "2024-03-14T07:56:07Z")
It works with 5 volts
---
### Author:  [@nicolasLGM](https://foil.zone/u/nicolasLGM)
#### Post date: [March 14, 2024, 8:08am UTC](https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725/47 "2024-03-14T08:08:04Z")
I tried with two BEC, and I also tried the BEC on the same flycolor xcross, the BEC works well, the receiver blue light is on (meaning receiver has current and remote is paired). I really hoped it was a BEC issue, but it’s not that. (I use 5V BEC).
It really seems that the ESC reboots each time I pull the trigger, (I see a vey litlle movement of the motor when I pull the trigger, and directly the 3 beeps of the arming sequence)
---
### Author:  [@FoiledBySpoil](https://foil.zone/u/FoiledBySpoil)
#### Post date: [March 14, 2024, 8:40am UTC](https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725/48 "2024-03-14T08:40:32Z")
Have you reverted all settings in the blheli32suite to factory default?
If e.g autotelemetry is on and has issues when pulling the trigger this could reboot the mcu in the ESC. Just an example tho…
---
### Author:  [@nicolasLGM](https://foil.zone/u/nicolasLGM)
#### Post date: [March 14, 2024, 8:53am UTC](https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725/49 "2024-03-14T08:53:22Z")
yes I reverted all settings to factory default, I also flashed to the latest firmware
Thanks for the idea, I will check again that telemetry is off
---
### Author:  [@Larsb](https://foil.zone/u/Larsb)
#### Post date: [March 14, 2024, 3:37pm UTC](https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725/50 "2024-03-14T15:37:13Z")
Maybe a mosfet is malfunctioning, can you remove the cover and check or is it potted?
---
### Author:  [@nekitesurfing](https://foil.zone/u/nekitesurfing)
#### Post date: [March 19, 2024, 5:32pm UTC](https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725/51 "2024-03-19T17:32:14Z")
Can I ask what thermal protection setting people have used on the 160a x cross esc? Thanks.
---
### Author:  [@kkolli](https://foil.zone/u/kkolli)
#### Post date: [March 23, 2024, 4:33pm UTC](https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725/52 "2024-03-23T16:33:08Z")
---
### Author:  [@Spearhunter](https://foil.zone/u/Spearhunter)
#### Post date: [March 25, 2024, 2:41pm UTC](https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725/53 "2024-03-25T14:41:26Z")
I found that at very low torque, and low trigger pull with the maytech remote, the motor is not spinning properly. Then when I seriously pull the trigger, It works nicely. Do you guys have the same behavior?
---
### Author:  [@lishine](https://foil.zone/u/lishine)
#### Post date: [March 27, 2024, 12:26pm UTC](https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725/54 "2024-03-27T12:26:45Z")
There is a deal now on Ali for X-Cross 160A at $62
[https://a.aliexpress.com/\_opBA3vO](https://a.aliexpress.com/_opBA3vO)
---
### Author:  [@Larsb](https://foil.zone/u/Larsb)
#### Post date: [March 27, 2024, 4:45pm UTC](https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725/55 "2024-03-27T16:45:06Z")
Might be a scam, i ordered the cheapest on ali around christmas, no package was sent within the guaranteed time so i cancelled the order.
---
### Author:  [@nicolasLGM](https://foil.zone/u/nicolasLGM)
#### Post date: [March 27, 2024, 4:51pm UTC](https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725/56 "2024-03-27T16:51:08Z")
I just ordered one 7 days ago at this price, and just received it this morning, seems real
---
### Author:  [@Larsb](https://foil.zone/u/Larsb)
#### Post date: [March 27, 2024, 4:51pm UTC](https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725/57 "2024-03-27T16:51:49Z")
I must congratulate👍
---
### Author:  [@Jatem](https://foil.zone/u/Jatem)
#### Post date: [March 28, 2024, 4:59am UTC](https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725/58 "2024-03-28T04:59:39Z")
Is the current protection setting measuring current at the battery, or at the phase wires?
I see that you’ve set current sense calibration to +100%, which would seem to double the reported current.
---
### Author:  [@JonathanC](https://foil.zone/u/JonathanC)
#### Post date: [March 28, 2024, 5:03am UTC](https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725/59 "2024-03-28T05:03:41Z")
Anyone waterproofing the X Cross in any way? Thinking might just soak in Corrosion X before installing.
---
### Author:  [@FoiledBySpoil](https://foil.zone/u/FoiledBySpoil)
#### Post date: [March 28, 2024, 2:23pm UTC](https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725/60 "2024-03-28T14:23:00Z")
Will dip mine hv3 in thermal epoxy when I receive it. pre-potting with silicone to ensure heat sinks stay exposed. Then removing the silicone. If anyone tried something similar already I’m eager to hear.
[Previous page](https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725.md?page=2)
[Next page](https://foil.zone/t/esc-flycolor-x-cross-hv3-settings-on-blheli-32/19725.md?page=4)