# Flipsky 100kv problem
**URL:** https://foil.zone/t/flipsky-100kv-problem/8632
**Category:** Electronics (ESC, remote, batteries)
**Created:** [July 18, 2020, 6:24pm UTC](https://foil.zone/t/flipsky-100kv-problem/8632 "2020-07-18T18:24:32Z")
**Posts on this page:** 19
**Page:** 1
### Author:  [@zaja.cz](https://foil.zone/u/zaja.cz)
#### Post date: [July 18, 2020, 6:24pm UTC](https://foil.zone/t/flipsky-100kv-problem/8632/1 "2020-07-18T18:24:32Z")
Hi guys, I have a problem with the Flipsky engine. The first test with the engine running, the engine just knocks and does not spin. The sound is like itโs spinning, but itโs running.๐ญ๐ญ๐ญ
---
### Author:  [@nice2cu](https://foil.zone/u/nice2cu)
#### Post date: [July 18, 2020, 6:32pm UTC](https://foil.zone/t/flipsky-100kv-problem/8632/2 "2020-07-18T18:32:15Z")
wich Controller are you using?
---
### Author:  [@zaja.cz](https://foil.zone/u/zaja.cz)
#### Post date: [July 18, 2020, 6:39pm UTC](https://foil.zone/t/flipsky-100kv-problem/8632/3 "2020-07-18T18:39:49Z")
I tried this for car models.!
ESC Is Flipsky 200A maybe I have to set something in ESC?
[IMG\_20200718\_203827\_1|666x500](https://foil.zone/uploads/short-url/zvZRhkgfa2UC7y9csl6Crj7gIsc.jpeg)
---
### Author:  [@Alexandre](https://foil.zone/u/Alexandre)
#### Post date: [July 18, 2020, 6:45pm UTC](https://foil.zone/t/flipsky-100kv-problem/8632/4 "2020-07-18T18:45:35Z")
Try to launch the spin by hand at the time
---
### Author:  [@zaja.cz](https://foil.zone/u/zaja.cz)
#### Post date: [July 18, 2020, 6:47pm UTC](https://foil.zone/t/flipsky-100kv-problem/8632/5 "2020-07-18T18:47:22Z")
Iโve tried that, but I canโt. donโt spin.๐ญ
as if a magnet were spinning on a shaft
---
### Author:  [@nice2cu](https://foil.zone/u/nice2cu)
#### Post date: [July 18, 2020, 6:49pm UTC](https://foil.zone/t/flipsky-100kv-problem/8632/6 "2020-07-18T18:49:24Z")
It is not possible to spin the axis?
Also not when without power?
---
### Author:  [@zaja.cz](https://foil.zone/u/zaja.cz)
#### Post date: [July 18, 2020, 6:50pm UTC](https://foil.zone/t/flipsky-100kv-problem/8632/7 "2020-07-18T18:50:50Z")
I turn the axis manually.
---
### Author:  [@zaja.cz](https://foil.zone/u/zaja.cz)
#### Post date: [July 18, 2020, 7:03pm UTC](https://foil.zone/t/flipsky-100kv-problem/8632/8 "2020-07-18T19:03:07Z")
when I add a minimum of gas, it does this. As if the ESC timing for the engine was wrong. Donโt know how much is the series Timing in Flipsky ESC and Flipsky engine?
---
### Author:  [@nice2cu](https://foil.zone/u/nice2cu)
#### Post date: [July 18, 2020, 7:22pm UTC](https://foil.zone/t/flipsky-100kv-problem/8632/9 "2020-07-18T19:22:15Z")
Did you run the motorwizzard in VESC tool?
---
### Author:  [@zaja.cz](https://foil.zone/u/zaja.cz)
#### Post date: [July 18, 2020, 7:26pm UTC](https://foil.zone/t/flipsky-100kv-problem/8632/10 "2020-07-18T19:26:22Z")
no, i just wanted to try it.๐ค
---
### Author:  [@nice2cu](https://foil.zone/u/nice2cu)
#### Post date: [July 18, 2020, 7:33pm UTC](https://foil.zone/t/flipsky-100kv-problem/8632/11 "2020-07-18T19:33:45Z")
dose not work like you do it.
You must run the motor Wizzard and defect the poles and timing ๐
---
### Author:  [@zaja.cz](https://foil.zone/u/zaja.cz)
#### Post date: [July 18, 2020, 7:41pm UTC](https://foil.zone/t/flipsky-100kv-problem/8632/12 "2020-07-18T19:41:01Z")
Thank you very much for the information. So I have to install the VESC tool program on the PC and set how much pole motor and timing I have? Iโm really stupid about this. Please write me here which values โโto change and for how much.๐
---
### Author:  [@nice2cu](https://foil.zone/u/nice2cu)
#### Post date: [July 18, 2020, 7:44pm UTC](https://foil.zone/t/flipsky-100kv-problem/8632/13 "2020-07-18T19:44:28Z")
Normally the motor Wizzard is enough.
Not change the firmware to no hardware limit ๐
---
### Author:  [@zaja.cz](https://foil.zone/u/zaja.cz)
#### Post date: [July 18, 2020, 7:48pm UTC](https://foil.zone/t/flipsky-100kv-problem/8632/14 "2020-07-18T19:48:28Z")
OK, thank you very muchโ:+1:๐๐
---
### Author:  [@Ackermann](https://foil.zone/u/Ackermann)
#### Post date: [July 18, 2020, 7:58pm UTC](https://foil.zone/t/flipsky-100kv-problem/8632/15 "2020-07-18T19:58:01Z")
Ofc run motor wizard and remote wizard first. Select large inrunner as config and work through the wizard. Ofc a brand-new esc will not work out of the box knowing nothing about the motor. If you have strange behavior and noise do not force several times. What you expect, the problem solve by itself ๐
Good luck!
I have Flipsky post for vesc, itโs not good but basic
---
### Author:  [@zaja.cz](https://foil.zone/u/zaja.cz)
#### Post date: [July 18, 2020, 8:04pm UTC](https://foil.zone/t/flipsky-100kv-problem/8632/16 "2020-07-18T20:04:14Z")
thank you very much ๐๐
---
### Author:  [@Alexandre](https://foil.zone/u/Alexandre)
#### Post date: [July 18, 2020, 9:10pm UTC](https://foil.zone/t/flipsky-100kv-problem/8632/17 "2020-07-18T21:10:28Z")
Wizard motor and remote , you can do that as well directly on motor settings page without going through the all select things โฆ
Config as well voltage settings ( cut off if the voltage is to low or high)
---
### Author:  [@zaja.cz](https://foil.zone/u/zaja.cz)
#### Post date: [July 19, 2020, 8:03pm UTC](https://foil.zone/t/flipsky-100kv-problem/8632/18 "2020-07-19T20:03:41Z")
Hi guys, so maybe I passed the setup successfully. I just noticed that when I add the throttle slowly, the engine spins smoothly. When I add plush faster, the spin is not smooth (it twitches) Do you have it anyway, or do I have a mistake somewhere?
---
### Author:  [@Ackermann](https://foil.zone/u/Ackermann)
#### Post date: [July 19, 2020, 8:59pm UTC](https://foil.zone/t/flipsky-100kv-problem/8632/19 "2020-07-19T20:59:59Z")
could be the cylindrical pin to hold the prop. the prop looks not very balanced.