# Looking for STL file for 65150 FR prop fairing
**URL:** https://foil.zone/t/looking-for-stl-file-for-65150-fr-prop-fairing/6480
**Category:** Props & Ducts
**Created:** [December 19, 2019, 7:15pm UTC](https://foil.zone/t/looking-for-stl-file-for-65150-fr-prop-fairing/6480 "2019-12-19T19:15:48Z")
**Posts on this page:** 8
**Page:** 2
### Author:  [@Flightjunkie](https://foil.zone/u/Flightjunkie)
#### Post date: [December 28, 2019, 7:21am UTC](https://foil.zone/t/looking-for-stl-file-for-65150-fr-prop-fairing/6480/21 "2019-12-28T07:21:26Z")
No worries. For now I just made this one fit. 🤙
---
### Author:  [@Darby](https://foil.zone/u/Darby)
#### Post date: [December 31, 2019, 11:24pm UTC](https://foil.zone/t/looking-for-stl-file-for-65150-fr-prop-fairing/6480/22 "2019-12-31T23:24:40Z")
This STL does not fit the Flipsky motor…
---
### Author:  [@Flightjunkie](https://foil.zone/u/Flightjunkie)
#### Post date: [December 31, 2019, 11:35pm UTC](https://foil.zone/t/looking-for-stl-file-for-65150-fr-prop-fairing/6480/23 "2019-12-31T23:35:22Z")
Yea. I had to modify it as depicted above. I’m terribly slow with fusion 360, so this was faster for now. I will post the modified STL if and when I get around to it.
But, it’s not hard to make fit. Took me all of 10 minutes.
🤙
---
### Author:  [@Darby](https://foil.zone/u/Darby)
#### Post date: [December 31, 2019, 11:45pm UTC](https://foil.zone/t/looking-for-stl-file-for-65150-fr-prop-fairing/6480/24 "2019-12-31T23:45:53Z")
Ok thanks- I’m modifying mine now… looking forward to the new print. 🕶
---
### Author:  [@Beninspain](https://foil.zone/u/Beninspain)
#### Post date: [June 4, 2020, 1:10pm UTC](https://foil.zone/t/looking-for-stl-file-for-65150-fr-prop-fairing/6480/25 "2020-06-04T13:10:17Z")
Did you ever get round to doing this for the maytech 12mm shaft?
Im about to reprint one in PC max, wondered if i still have to modify this with my dremel?
---
### Author:  [@Flightjunkie](https://foil.zone/u/Flightjunkie)
#### Post date: [June 4, 2020, 4:53pm UTC](https://foil.zone/t/looking-for-stl-file-for-65150-fr-prop-fairing/6480/26 "2020-06-04T16:53:30Z")
@michion edited the two files. I’ll have to look for the post.
…here you go!
Thanks again Michion!
🤙
> **[Fr 2019 motor system](https://foil.zone/t/fr-2019-motor-system/3762/541)**
>
> All good. This one should fit either of the flipsky motors. Sounds like you have a mashup of both motors above. I didnt know about the one with the wider cone. Plus I removed the space for the extra lip seal on the outside as the motor already...
---
### Author:  [@Beninspain](https://foil.zone/u/Beninspain)
#### Post date: [June 4, 2020, 5:17pm UTC](https://foil.zone/t/looking-for-stl-file-for-65150-fr-prop-fairing/6480/27 "2020-06-04T17:17:44Z")
Thankyou. Knew I had seen it somewhere.
---
### Author:  [@philippe](https://foil.zone/u/philippe)
#### Post date: [September 26, 2021, 3:12pm UTC](https://foil.zone/t/looking-for-stl-file-for-65150-fr-prop-fairing/6480/28 "2021-09-26T15:12:08Z")
Hello
Do you have the “360 fusion” file for the Flipsky 65161 motor duct, thank you
[Previous page](https://foil.zone/t/looking-for-stl-file-for-65150-fr-prop-fairing/6480.md?page=1)