# VESC 75100 cut off under load at 63% throttle
**URL:** https://foil.zone/t/vesc-75100-cut-off-under-load-at-63-throttle/18586
**Category:** Build, Repair & Mod
**Tags:** vesc
**Created:** [July 10, 2023, 5:46am UTC](https://foil.zone/t/vesc-75100-cut-off-under-load-at-63-throttle/18586 "2023-07-10T05:46:43Z")
**Posts on this page:** 20
**Page:** 1
### Author:  [@vib.dxb](https://foil.zone/u/vib.dxb)
#### Post date: [July 10, 2023, 5:46am UTC](https://foil.zone/t/vesc-75100-cut-off-under-load-at-63-throttle/18586/1 "2023-07-10T05:46:43Z")
Gents,
been running on 75100 from flipsky for a long time now. started a new build for my foil assist with outrunner 6384. always set up the same way , updating the firmware 75\_300\_R2 , filter false…etc …
running on 12S with 200 A max current … whatever I do , at 63% throttle the motor stop ? … i m on a 47 litre board ans small front wing so I just need a bit extra power to fly … i can run at 50% for ever, nothing happens ? first time I have this problem ? will share my set up screens if needed ?
---
### Author:  [@Strongarm](https://foil.zone/u/Strongarm)
#### Post date: [July 10, 2023, 6:24am UTC](https://foil.zone/t/vesc-75100-cut-off-under-load-at-63-throttle/18586/2 "2023-07-10T06:24:50Z")
Hey I’ve had similar issue in the past, a sudden loss of power was due to too low of a battery current limit. Another time was running in Duty Cycle control (new controller/ receiver test), and for some reason (even spinning in air) i would get ABS\_current\_limit or something like that on the laptop when connected and running.
Are you running Duty Cycle or Current Control on the VESC?
What is the battery current limit set at?
Does it do it in the air, and the water?
Does the motor run smooth, or is there stuttering/ cogging?
Have you run the motor set up with correct poles/ outrunner size via the wizard?
---
### Author:  [@vib.dxb](https://foil.zone/u/vib.dxb)
#### Post date: [July 10, 2023, 7:09am UTC](https://foil.zone/t/vesc-75100-cut-off-under-load-at-63-throttle/18586/3 "2023-07-10T07:09:18Z")
thanks for the help
Are you running Duty Cycle or Current Control on the VESC?
current control
What is the battery current limit set at?
need to check but 200A I have no BMS, I read on Flipsky webpage that max current thats what I changed from previous set up
[ ](https://cdn.shopifycdn.net/s/files/1/0011/4039/1996/files/VESC_TOOL.png?v=1660544516)
Does it do it in the air, and the water?
air no problem , water is the problem under load after 63% throttle
Does the motor run smooth, or is there stuttering/ cogging?
running fine
Have you run the motor set up with correct poles/ outrunner size via the wizard?
good question , I never check with 6384 motor but I believe it was showing 4 and I put 3 ?
---
### Author:  [@Larsb](https://foil.zone/u/Larsb)
#### Post date: [July 10, 2023, 7:46am UTC](https://foil.zone/t/vesc-75100-cut-off-under-load-at-63-throttle/18586/4 "2023-07-10T07:46:18Z")
6384 is a 12-slot / 14-pole motor so it should be 14 poles or 7 pole pairs in the settings.
---
### Author:  [@vib.dxb](https://foil.zone/u/vib.dxb)
#### Post date: [July 10, 2023, 7:54am UTC](https://foil.zone/t/vesc-75100-cut-off-under-load-at-63-throttle/18586/5 "2023-07-10T07:54:46Z")
yes will try that …and repport …thanks
---
### Author:  [@sat\_be](https://foil.zone/u/sat_be)
#### Post date: [July 10, 2023, 10:34am UTC](https://foil.zone/t/vesc-75100-cut-off-under-load-at-63-throttle/18586/6 "2023-07-10T10:34:38Z")
Pole pairs won’t change anything really, this is just needed to calculate real rpm (derived from erpm). Is it giving you an error when it stops? What FW version are you using?
I think you can go higher with motor current max. As a reference, I use a 63100 on a makerxHi75200, max motor current is 158A, Batt on 105, abs max current 250A.
There is a good thread on the different 75100/200 versions here: [How to update firmware on the Flipsky 75100 & 75200 FOC ESC - The Citadel - Essential References for Esk8 - esk8.news: DIY Electric Skateboard Forums](https://forum.esk8.news/t/how-to-update-firmware-on-the-flipsky-75100-75200-foc-esc/61819)
---
### Author:  [@vib.dxb](https://foil.zone/u/vib.dxb)
#### Post date: [July 10, 2023, 10:58am UTC](https://foil.zone/t/vesc-75100-cut-off-under-load-at-63-throttle/18586/7 "2023-07-10T10:58:24Z")
thanks I saw this thread but before I only apply the standard FW by uploading trhough VESC tool…so unless it has changed I don-t undersdtanbd what I m doing wrong .,… I will recude the Amps on motor current and chech FW version…
---
### Author:  [@SoEFoil](https://foil.zone/u/SoEFoil)
#### Post date: [July 10, 2023, 4:57pm UTC](https://foil.zone/t/vesc-75100-cut-off-under-load-at-63-throttle/18586/8 "2023-07-10T16:57:53Z")
What remote model ? On a Flipsky VX3 remote, switching the gear from H to M is built for this purpose
---
### Author:  [@vib.dxb](https://foil.zone/u/vib.dxb)
#### Post date: [July 11, 2023, 3:10am UTC](https://foil.zone/t/vesc-75100-cut-off-under-load-at-63-throttle/18586/9 "2023-07-11T03:10:42Z")
no i m using the maytech …nothing has changed in my set up who has been working for years … anyway need to twich a little and I will repport
---
### Author:  [@vib.dxb](https://foil.zone/u/vib.dxb)
#### Post date: [July 17, 2023, 5:00am UTC](https://foil.zone/t/vesc-75100-cut-off-under-load-at-63-throttle/18586/10 "2023-07-17T05:00:15Z")
> [@sat\_be](#):
>
> There is a good thread on the different 75100/200 versions here: [How to update firmware on the Flipsky 75100 & 75200 FOC ESC - The Citadel - Essential References for Esk8 - esk8.news: DIY Electric Skateboard Forums](https://forum.esk8.news/t/how-to-update-firmware-on-the-flipsky-75100-75200-foc-esc/61819)
so I upgrade this firmware and seems to work now. each time I connect got a message asking to upgrade the firmware..just ignore it and it works …
---
### Author:  [@Eugenio](https://foil.zone/u/Eugenio)
#### Post date: [July 17, 2023, 5:43am UTC](https://foil.zone/t/vesc-75100-cut-off-under-load-at-63-throttle/18586/11 "2023-07-17T05:43:25Z")
HI, I was have This problem 2 years ago, it was ABS\_current\_limit, you need n Ablolute maximum current write more about 50a as motor current max, for example motor current max 120a, absolute current max 170a.
---
### Author:  [@BasNL](https://foil.zone/u/BasNL)
#### Post date: [July 9, 2024, 1:48pm UTC](https://foil.zone/t/vesc-75100-cut-off-under-load-at-63-throttle/18586/12 "2024-07-09T13:48:43Z")
I’m experiencing similar issues!
Anywhere near 3/4 to max throttle the power cuts. It’s a brand new 75100 vesc with 6384 motor.
With the small board I’m fully the nose so when power cuts I get a hard facedive 🫤
.
For testing I’ve changed all cutoff settings to absurdly high values, but still same issue. Even tried battery save at 35V.
It feels like the prop starts cavitating or vibrating just before it cuts out.
Any other suggestions here?
Edit, added screenshot:
---
### Author:  [@Strongarm](https://foil.zone/u/Strongarm)
#### Post date: [July 9, 2024, 2:39pm UTC](https://foil.zone/t/vesc-75100-cut-off-under-load-at-63-throttle/18586/13 "2024-07-09T14:39:27Z")
Try run it in a bucket with the serial cable connected. You might get an error which can help you diagnose.
Make sure you have phase filters turned off otherwise you could cook something.
I once had a vesc that would only run nicely in BLDC mode and not in FOC. So you could try that as well.
---
### Author:  [@Jezza](https://foil.zone/u/Jezza)
#### Post date: [July 9, 2024, 3:15pm UTC](https://foil.zone/t/vesc-75100-cut-off-under-load-at-63-throttle/18586/14 "2024-07-09T15:15:35Z")
Have you changed the power setting?
---
### Author:  [@vib.dxb](https://foil.zone/u/vib.dxb)
#### Post date: [July 9, 2024, 4:07pm UTC](https://foil.zone/t/vesc-75100-cut-off-under-load-at-63-throttle/18586/15 "2024-07-09T16:07:32Z")
try these values
Motor Current Max 150A
Motor current max brake -150A
Absolute maximum current 200A
show abs current limit. ;;;False ?
battery current max 125A
battery current max regen -125A
I beliebe that fixed my issues
---
### Author:  [@sat\_be](https://foil.zone/u/sat_be)
#### Post date: [July 9, 2024, 7:00pm UTC](https://foil.zone/t/vesc-75100-cut-off-under-load-at-63-throttle/18586/16 "2024-07-09T19:00:19Z")
High brake current means that the propeller immedietely stops if you release the trigger. Maybe not what we want on a foil.
---
### Author:  [@Pavel](https://foil.zone/u/Pavel)
#### Post date: [July 9, 2024, 7:14pm UTC](https://foil.zone/t/vesc-75100-cut-off-under-load-at-63-throttle/18586/17 "2024-07-09T19:14:44Z")
Have you installed the firmware for ESC 75300 on ESC 75100?
It may just be a coincidence, but 200A/3 = 66A, that’s 66% of your regulator’s maximum 100A.
Try setting the settings to a maximum of 300A, maybe this will help you.
---
### Author:  [@Strongarm](https://foil.zone/u/Strongarm)
#### Post date: [July 9, 2024, 11:35pm UTC](https://foil.zone/t/vesc-75100-cut-off-under-load-at-63-throttle/18586/18 "2024-07-09T23:35:02Z")
The power setting wouldn’t make an abrupt stop, it would just limit it.
---
### Author:  [@Pavel](https://foil.zone/u/Pavel)
#### Post date: [July 10, 2024, 12:12am UTC](https://foil.zone/t/vesc-75100-cut-off-under-load-at-63-throttle/18586/19 "2024-07-10T00:12:56Z")
---
### Author:  [@Pavel](https://foil.zone/u/Pavel)
#### Post date: [July 10, 2024, 12:18am UTC](https://foil.zone/t/vesc-75100-cut-off-under-load-at-63-throttle/18586/20 "2024-07-10T00:18:24Z")
@vib.dxb also try setting the voltage limit much lower, two times less than now.
[Next page](https://foil.zone/t/vesc-75100-cut-off-under-load-at-63-throttle/18586.md?page=2)