# Vx3 & 75100/75200
**URL:** https://foil.zone/t/vx3-75100-75200/16885
**Category:** Electronics (ESC, remote, batteries)
**Tags:** vesc
**Created:** [October 6, 2022, 7:40am UTC](https://foil.zone/t/vx3-75100-75200/16885 "2022-10-06T07:40:42Z")
**Posts on this page:** 20
**Page:** 1
### Author:  [@KLAUSMOLLERZIP](https://foil.zone/u/KLAUSMOLLERZIP)
#### Post date: [October 6, 2022, 7:40am UTC](https://foil.zone/t/vx3-75100-75200/16885/1 "2022-10-06T07:40:42Z")
Hello, I have searched the entire forum but I have not found the solution to configure the FLIPSKY VX3 and a FLIPSKY 75100 or 75100 with VESC TOOL.
I can’t see the temperature of the VESC, or Amps, or Watts.
Does anyone have the same problem or has it configured correctly?
this is my setup
I have already tried to change RX and TX
Thank you
---
### Author:  [@Toto44](https://foil.zone/u/Toto44)
#### Post date: [October 6, 2022, 8:38am UTC](https://foil.zone/t/vx3-75100-75200/16885/2 "2022-10-06T08:38:10Z")
What esc type is Set in the Remote?
---
### Author:  [@KLAUSMOLLERZIP](https://foil.zone/u/KLAUSMOLLERZIP)
#### Post date: [October 6, 2022, 9:21am UTC](https://foil.zone/t/vx3-75100-75200/16885/3 "2022-10-06T09:21:48Z")
the set in remote is VESC
---
### Author:  [@Toto44](https://foil.zone/u/Toto44)
#### Post date: [October 6, 2022, 9:58am UTC](https://foil.zone/t/vx3-75100-75200/16885/4 "2022-10-06T09:58:54Z")
Try fsesc
20 character
---
### Author:  [@KLAUSMOLLERZIP](https://foil.zone/u/KLAUSMOLLERZIP)
#### Post date: [October 6, 2022, 11:42am UTC](https://foil.zone/t/vx3-75100-75200/16885/5 "2022-10-06T11:42:25Z")
> [@Toto44](#):
>
> 20 character
20 character?
i dont understand, where can i choose this option? in the the Remote?
---
### Author:  [@Toto44](https://foil.zone/u/Toto44)
#### Post date: [October 6, 2022, 12:10pm UTC](https://foil.zone/t/vx3-75100-75200/16885/6 "2022-10-06T12:10:33Z")
Yes choose in the remote
20 character is only to get at least 20 character 😂😂
Just choose fsesc as esc in the vx3 and try
Hier ab 4:30
[ ](https://www.youtube.com/watch?v=0AeHIvXW6JQ)
---
### Author:  [@KLAUSMOLLERZIP](https://foil.zone/u/KLAUSMOLLERZIP)
#### Post date: [October 6, 2022, 1:35pm UTC](https://foil.zone/t/vx3-75100-75200/16885/7 "2022-10-06T13:35:11Z")
Hi Toto44
nothing, with FSESC it does not send any data.
in the WIZARD, the only thing that matches is the NRF controller. It calibrates the VX3 trigger fine but then it doesn’t send any data.
---
### Author:  [@Toto44](https://foil.zone/u/Toto44)
#### Post date: [October 6, 2022, 2:27pm UTC](https://foil.zone/t/vx3-75100-75200/16885/8 "2022-10-06T14:27:22Z")
Vesc remote does not work in vesc tool???
---
### Author:  [@KLAUSMOLLERZIP](https://foil.zone/u/KLAUSMOLLERZIP)
#### Post date: [October 6, 2022, 2:43pm UTC](https://foil.zone/t/vx3-75100-75200/16885/9 "2022-10-06T14:43:34Z")
I mean that in the VESC TOOL I execute the WIZARD in NRF controller, and it recognizes it perfectly. And the remote trigger raises and lowers Duty on VESC TOOL, but dont shows temp, W, amp…
---
### Author:  [@Toto44](https://foil.zone/u/Toto44)
#### Post date: [October 6, 2022, 7:33pm UTC](https://foil.zone/t/vx3-75100-75200/16885/10 "2022-10-06T19:33:54Z")
Try to use vesc remote in the vesc software. Choose vesc remote an then current no reverse.
---
### Author:  [@osavcic](https://foil.zone/u/osavcic)
#### Post date: [October 6, 2022, 10:35pm UTC](https://foil.zone/t/vx3-75100-75200/16885/11 "2022-10-06T22:35:34Z")
…make sure the RT button on the right side of the Vesc tool is turned on
---
### Author:  [@KLAUSMOLLERZIP](https://foil.zone/u/KLAUSMOLLERZIP)
#### Post date: [October 7, 2022, 7:34am UTC](https://foil.zone/t/vx3-75100-75200/16885/12 "2022-10-07T07:34:02Z")
yes of course it’s on
---
### Author:  [@Toto44](https://foil.zone/u/Toto44)
#### Post date: [October 7, 2022, 7:40am UTC](https://foil.zone/t/vx3-75100-75200/16885/13 "2022-10-07T07:40:48Z")
Did you try the vesc remote? Set it from “OFF” to “current no reverse”
---
### Author:  [@KLAUSMOLLERZIP](https://foil.zone/u/KLAUSMOLLERZIP)
#### Post date: [October 7, 2022, 7:55am UTC](https://foil.zone/t/vx3-75100-75200/16885/14 "2022-10-07T07:55:46Z")
---
### Author:  [@Toto44](https://foil.zone/u/Toto44)
#### Post date: [October 7, 2022, 12:10pm UTC](https://foil.zone/t/vx3-75100-75200/16885/15 "2022-10-07T12:10:01Z")
did you connect the wire from the receiver to the battery + ?
---
### Author:  [@KLAUSMOLLERZIP](https://foil.zone/u/KLAUSMOLLERZIP)
#### Post date: [October 7, 2022, 4:42pm UTC](https://foil.zone/t/vx3-75100-75200/16885/16 "2022-10-07T16:42:22Z")
no, but it is assumed that via UART it is not necessary, like temperature
---
### Author:  [@mlab](https://foil.zone/u/mlab)
#### Post date: [December 6, 2022, 10:46pm UTC](https://foil.zone/t/vx3-75100-75200/16885/17 "2022-12-06T22:46:26Z")
It looks like it says RP on the remote in the top left of vx3. That means it’s connected using PPM not UART. When connected to UART it will show RU. You need to connect the receiver to the COMM/UART port on the VESC (4 wires) and then configure your VX3 to be in VESC or FCESC mode.
Then ensure you set the VESC-tool to Current or Current no reverse as shown above
---
### Author:  [@mlab](https://foil.zone/u/mlab)
#### Post date: [December 6, 2022, 10:53pm UTC](https://foil.zone/t/vx3-75100-75200/16885/18 "2022-12-06T22:53:18Z")
Also don’t forget to setup in App setting → general. You need to set App to Use to UART. That one took me forever to figure out. And don’t forget to write the config to the VESC by clicking the approciate non-intuative icon on the right side of the UI. It’s one of the As with an arrow (down arrow I think )
---
### Author:  [@lukmo](https://foil.zone/u/lukmo)
#### Post date: [December 7, 2022, 9:44am UTC](https://foil.zone/t/vx3-75100-75200/16885/19 "2022-12-07T09:44:11Z")
Is there any easy way to use duty control with VX3?
---
### Author:  [@KLAUSMOLLERZIP](https://foil.zone/u/KLAUSMOLLERZIP)
#### Post date: [December 7, 2022, 2:53pm UTC](https://foil.zone/t/vx3-75100-75200/16885/20 "2022-12-07T14:53:52Z")
Thanks, i’ll try in a few days
[Next page](https://foil.zone/t/vx3-75100-75200/16885.md?page=2)