Hi
I download this file on fusion and I have different parts of project
How obtaining 2 parts assembled (master clamp front and back) on same plan ?
Regards
Giloris
If you use the file I linked to you should have the whole unit assembled, including all mast parts, motor, prop etc.
@giloris, use the fusion file linked below when you follow the video instruction. Good luck!
Custom Masts - This video shows how to quickly adjust the mast clamp to your own foil mast in Fusion 360. The fusion assembly comes with LF 2017 and Axis mast designs but you can adapt it to any mast. Here is the CAD file I use in the video, same components are referenced by the full CAD assembly listed above.
1 Like
Hi
Thank you for your vidéo it s help me very more
But i havé à question how do you built geometric figure with différents point Line (function do you use in fusion ?)
How do you ajust the two parts when thé new mast is inside at thé end ?
Regards
Giloris
Hi
Can you say me how building this figure (what function using on fusion 360 ?)
Regards
Giloris
What do you want to achieve?
Do you want to make a 3D Profile form your 2D Shape? → Use the Extrude command. Create->Extrusion (Keyboard shortcut ‘E’). Then drag the arrow to the right length or specify the length.
Here @charlieuk posted a tutorial on creating wings in Fusion 360:
1 Like
Hi thank you for your help.
I follow pacificmeister tuto to modify mast width from canvas function. He build a geometric figure (picture) but I don’t know fusion command use to built i. I understand other steps, extrusion …
Regards
Giloris
I don’t understand the problem. You don’t need to build anything yourself, it is all there you just need to modify it slightly as shown in the video:
Rewind the timeline, edit the mast profile sketch according to your mast picture, fast-forward the timeline again and it will build everything up according to the new modified sketch of your own mast.
hi sorry
I don’t have upload CAD file on A360
I understand my error.
Regards
Giloris
Hi friends,
This is Elle from Shenzhen Waydoo Intelligence Technology company. hope I didn’t disturb you.
We hereby sincerely invite you and your company representatives to visit our booth at Singapore Yacht Show from April 11st to 14th 2019.
At the show, we’ll present you the most advanced Electronic Hydrofoil-- Waydoo Flyer at unbeatable price.
Demo Activities Time : 4:00-5:00 pm 11st -14th April.
Booth No: A-H4 & A-H5 (Floating Leisure Hub).
Add: ONE 15 Marina Sentosa Cove, Singapore.
Looking forward to your arrival!
Elle
elle.lin@waydoo.io
+86 13724266101
1 Like
Ouch! How did that happen!?! So much for Bomb proof!
1 Like
I am wondering who bought this foil and is their E-foil speed about the same as mine. I seem to foil the best at 12 to 14 mph. Any faster and I climb out of the water.
Ive got this foil, I can get it to a little over 35kph (21.9 mph) and it doesn’t seem too bad to control, maybe a little sketchy at 35kph. But it uses a fair bit of power to hold that speed compared to the Slingshot 76cm surf wing because it has a pretty thick cross section.
2 Likes
I have gone 17mph, I probably could go 20 if I was not scared, the motor seems to have the power.
What would be the typical application of the foil I have? SUP foiling?
Got any suggestions for a higher speed reasonably priced “Chinese” foil for my next build?
This one looks like the takuma V100 and the gong M , perfect for freestyle 20-30km/h , up to 35km/h
Have you look at the new gong M pro ?
1 Like
My foil does look just like the takuma V100, So its a very slow easy to ride foil? That is exactly what I wanted for my first E-foil. I will read about the gong M pro foil.
wherein germany is that?
Markkleeberger See close to Leipzig. That’s the one where the great Efoil Meetup few weeks ago have been took place.
1 Like
