Great minds think alike friend. This is the subject matter motor. I’m essentially asking if i can get it in 250Kv. Highest KV i saw for the 80100 was 200kv and on 18s. Which would be fine by the way… i’d try that exact motor but out of stock. One of the things i challenged Bruno to answer was motor availability.
" PLEASE NOTE: Alien Electronics LTD adopts a continuous development program which sometimes necessitates specification changes without notice. Pictures of products and information in the instructions manual are for reference only and can be changed without notice at any time. Colors of goods are subject to stock availability"
So i’m a supplier quality engineer. Someone who puts that blanket statement on their product is essentially saying it is not their product. He has no control over the supply chain. These are Chineese motors sourced by him and that’s why the price is as low as it is. I doubt he will be able to supply any custom motor KV unless it’s coupled with an order of 50-100 or more.
Use that same calculator but with the TP100 (120kv). Use 8nm as the goal @ 15,000rpm. It pulls 125v to achieve it at 100a but shows 96.5% efficiency of 13kw.
Then we modify the jet to load 15k rpm at 100a and take advantage of all 13kw electrical power. Thats kinda what i want to do currently. I dont know 100v is any more dangerous than 50v when it gets dunked into water. Just need to take some serious steps a short-out can’t happen and if it does it blows the bms or fuse instead of the pack.
Also second guessing what i said there. There probably is a safe limit of voltage at some point here. A short circuit to your feet could literally mean death at these voltages. Not just injury.
This makes things simpler in terms of power goal but also more complex in terms of wanting a single jet design. If we keep the 50v safety limit with the 100a heat limit you have a solid 5000w limitation per drive. If you want a 10kw board you’d NEED two jets and wiring(battery) that’s cool with 200a loads.
I would say the safest limit is 14S. Explanations here :
That’s also why most of the jetboards are running 12S or 14S maximum. You’ll need a solid 200A ESC but that’s still doable.
Btw, anyone willing to share some technical specs on the Radinn boards ? I don’t find any info on their battery / jet diameter, impeller, motor or whatever…
re Radinn boards,
I would love to get a board template of it!
I love the way they look. However they are pretty thick!
The EXPLORE and FREERIDE are 17 cm thick, and the CARVE is 16 cm!
Efoil boards are also in the range of 13-15cm thick to put the battery in it
Well I am more interested to know what inside (technically speaking) So far the only info I found is that they use a 12kW motor for their fastest jetpack ! Would someone with some more info dare to chime in ?
My version 1 of the jetboard is 10cm. The motor box is 1 cm higher. So theoretically 11 cm should be enough. The new board we are building will be 13 cm thick.
And yes. Sure we are also interested in the electronic / motor / jet info.
Yeah i’m starting to think they went with a TP100. I can get one wound to 15,000rpm @ 58v too. Only motors rated to that type of wattage on a single unit. The thickness also helps with buoyancy. You could have a shorter board that is thicker and still float without moving. Then when you do plane you have less surface area on the water.
wonder if you have see other’s comments. the waterproof is done to the connection between battery and the motors. the compartment itself is not waterproof. this is the popular design among lift, fliteboard and waydoo.
Agreed. I personally love the design. The thickness makes sense when you consider those things, and trying to cram in a 10cm/4" motor in there. Some 250 cells to make up the battery will take up some space too. What i’m starting to get concerned about is design weight. TP100 and a pack to run it i’m seeing around 30lbs/14kg. That’s no board, jet or esc yet… though those are the lighter variety.
Yes the Raddin Explorer and Freeride do look broad, but the Carve does not.
The board we are shaping now is 190 cm by max width 70 by 13 cm thick.
Doing the maths gives us around 170 liters!. Way bigger than what I’m riding now (just over 100 liters)
It is the thickness from the new board causing the liters to be so big.
We might chop some from the nose (10cm), and could do the same with the tail.
After this the volume will be around 150 liters.
This will also bring the max width even more back… Could be a good thing.
However… A short board could also be a bit more nerves when riding!
That’s them!!! They totally look like the supplier for the 83100 line Alienpowersystems carries. Bruno couldn’t make the meeting today so i was left with continuing the search for new options. I’m straying from 83mm over to 100mm in consideration of the single jet.
The 80100 is going to be whats required from the 65mm jet i doubt it will do for 80mm but i have no idea. The problem with the 80100 is the power limit. It’s limited to 7000w if you use every bit of it’s power(we wont). You are hearing most board manufacturers are having 12kw power ratings to achieve what they do. So if you want two 65mm jets you could totally run the 80100. I want a 12kw single-jet board, so to the 100mm motors i go.
?